PDF download Download Article PDF download Download Article

Most digital safes have a key you can use to unlock and open them instead of using the passcode. But what do you do if you lose your digital safe key and there's no power to the keypad? This wikiHow article will walk you through getting back into your digital safe without the key or code, including tips for fixing the keypad, resetting the code, and—if worse comes to worse—breaking in.

Method 1
Method 1 of 3:

Restoring Power to the Keypad

PDF download Download Article
  1. Some digital safes have a keypad for your passcode as well as an override key that can unlock the safe. If your electronic keypad has run out of power, and you don’t have your override key, replace the batteries that power the keypad or recharge the keypad.[1]
    • If you don’t have your override key, you can access your digital safe is by using the electronic keypad.
  2. Search near or on the keypad for the battery casing. It can usually be found on the underside of the keypad. Use your finger to hold the latch and remove the casing to expose the batteries.[2]
    • Some digital safes may require you to remove a small screw to access the battery casing.
    • Check to make sure the battery casing isn’t damaged or the pieces are falling out. If so, you may need to take your safe to a professional to have it opened.
    Advertisement
  3. Once you’ve opened the battery casing, take out the existing batteries from their slots. Install the same type of batteries into their slots the same way the previous ones were installed. Then, close the battery case latch.[3]
    • The keypad may light up or lights may turn on once you restore power to it.
  4. If your safe has a USB slot or a slot for a power cord, or a 9-volt battery on the keypad, plug in an electrical cord or battery that fits into it. Allow the keypad to charge for at least 10 minutes before you try to access the safe so it has a chance to build up a power reserve.[4]
    • If your safe has a USB charging port, it will accept any USB charging cord.
    • Your safe may have a specific power cord used to charge the keypad, but you may be able to find a cord that fits into the charging port.
    • There should be a charging light that comes on or a light behind the keypad that is activated when you plug a power supply into it.
  5. Once the keypad has power, try entering your passcode. The locking mechanism will disengage and you’ll be able to open and access your digital safe.[5]
    • If you’ve forgotten your passcode, try resetting it.
  6. Advertisement
Method 2
Method 2 of 3:

Resetting Your Passcode

PDF download Download Article
  1. Look for small holes or openings on the back or the bottom of the safe. Shine a flashlight through the holes and look inside for the backside of the control panel.[6]
    • There will be wires and electrical components on the back of the control panel.
  2. Take a wire coat hanger, unwind it, and straighten it out so it’s a long, thin wire. Slide the end of the wire hanger into 1 of the openings so you can access the control panel.[7]
    • Be careful not to jam the wire hanger into the opening or you could potentially damage the electronic keypad and be unable to reset it.

    Tip: If you don’t have a wire coat hanger, or if the opening is too small for one, use a small, stiff wire that is long enough to reach the control panel.

  3. Using your flashlight to guide the wire, look for the reset button on the backside of the control panel. It should be a small, black button with the word “Reset” next to it. Push the button with the end of the hanger.[8]
    • You may hear a beeping sound or the control panel may light up when you press the reset button.
  4. Once you’ve pressed the reset button, you’ll be able to enter a new passcode on the front of the keypad. Type in a code that you know you’ll remember on the keypad.[9]
    • Write down the code or save it into your phone so you won’t lose it!
  5. Shine the flashlight through one of the openings and look for a button next to the reset button labeled “Set.” Press the button with the end of your wire to confirm the new passcode that you entered.[10]
    • The control panel may beep or light up after you confirm the code.
    • The set button may not be labeled or it may have a checkmark on the front of the panel.
  6. Remove the wire from the safe and enter your new code into the control panel on the front of the safe. Then, open up your safe after the locking mechanism is disengaged.[11]
  7. Advertisement
Method 3
Method 3 of 3:

Trying Other Solutions

PDF download Download Article
  1. If your digital safe has a keyhole, stick the pointed tip of a sturdy knife into it. Shake and wiggle the knife to force the locking mechanism to disengage. Then, open the door of the safe.
    • Shaking the lock open will more likely work for cheaper safes.
    • This solution may work well on a combination key and digital keypad safe.
  2. Place the safe on a flat surface and insert a flathead screwdriver into the keyhole. Rotate the screwdriver counterclockwise over and over until you hear or feel the locking mechanism break open. Then, remove the screwdriver and open the safe.
    • You may not be able to lock the safe again after damaging the locking mechanism with a screwdriver.
  3. If all else fails, take a power drill and attach a drill bit strong enough to drill through metal. Drill through the key slot on the safe until you penetrate all the way through, which will disable the locking mechanism. You can then open the safe door.[12]

    Note: Drilling through the safe may be difficult to do and could damage your power drill.

  4. Advertisement


Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!

You Might Also Like

Restart Your Computer Using the KeyboardRestart Your Computer Using the Keyboard
Check Browsing History on a WiFi RouterCheck Browsing History on a WiFi Router
Connect PC to TV with HDMIConnect PC to TV with HDMI
Find the Publication Date of a Website3 Easy Ways to Find the Publication Date of a Website
Pair Jbl Earbuds6 Ways to Pair Your JBL Earbuds: Guide & Troubleshooting Tips
What Does DW MeanWhat Does DW Mean? Snapchat, Texting, and More
Cheat a Step Counter on a Phone10 Genius Ways to Cheat a Step Counter on a Phone (No Walking Required)
Listen to Police RadioHow to Listen to Police Radio Online: Best Apps & Websites
Read Dump FilesEasy Ways to Read Crash Dump Files & Troubleshoot Crashes
Bypass Screen Time PasscodeHow to Bypass Your Screen Time Passcode: Reset, Remove, or Hack Screen Time
Guess a PasswordHow to Guess a Password
Tell if Your Mac Is Too Old to UpdateTell if Your Mac Is Too Old to Update
Change Mouse Polling RateEasy Ways to Adjust Your Mouse Polling Rate on PC & Mac
Connect a Laptop to a ProjectorConnect a Laptop to a Projector
Advertisement

Expert Interview

Thanks for reading our article! If you’d like to learn more about opening a lock, check out our in-depth interview with Robert Vallelunga.

About This Article

Robert Vallelunga
Co-authored by:
Locksmith
This article was co-authored by Robert Vallelunga. Robert Vallelunga is a Locksmith and the Owner of ACME Locksmith in the Phoenix Metro Area. Robert has over 15 years of experience in the industry and specializes in working with automotive ignitions, locks, keys, and master key systems. Robert and the team at ACME are the #1 Rated Phoenix Locksmith Service and the Winner of the Better Business Bureau Ethics Award. Robert has his Residential & Commercial Contractor’s License and a Bachelor of Science in Electrical Engineering from Arizona State University. This article has been viewed 569,380 times.
How helpful is this?
Co-authors: 10
Updated: February 28, 2024
Views: 569,380
Thanks to all authors for creating a page that has been read 569,380 times.

Is this article up to date?

Advertisement